Timber and concrete upper floors

6.4.19Floor decking

Floor decking shall be suitable for the intended use and be of adequate strength and moisture resistance. Issues to be taken into account include:

  1. type, thickness and fixing
  2. protection against damage.

Type, thickness and fixing

Where decking contributes to the sound insulation of a floor, the thicknesses listed in this chapter should be checked.

Floor decking should:

  • be appropriate to the joist spacing
  • be in accordance with Table 7 (which applies to normal domestic loads, i.e. an imposed load of 1.5kN/m2), or comply with another acceptable clause described in Technical Requirement R3.

Table 7: Floor decking requirements

Floor decking400mm joist centres450mm joist centres600mm joist centresStandard
Softwood boarding 161619BS EN 13353
Moisture resistant chipboard 181822BS EN 312 – type P5
Plywood151518/19BS EN 636
Oriented strand board151518/19BS EN 300 – type OSB3

When installing decking:

  • fixings and support should be in accordance with the manufacturer’s recommendations
  • checks should be made, prior to fixing, to ensure that noggings, blocking and strutting are in the correct position and secure
  • butt joints should be staggered and supported on noggings or joists
  • adjacent boards should be square
  • where nails are used, they should be 2.5 x the thickness of the decking material
  • where gluing is required, boards should be glued to the joists and at joints, using a suitable polyvinyl acetate (PVAc) adhesive
  • temporary wedges and packing should be removed once the floor decking is complete.

Square edged boards and boards with loose tongues

When fixing boards with square edges or loose tongues, they should be supported on all sides by joists or noggings.

Tongued and grooved boards

When fixing boards with tongued and grooved edges:

  • boards should be laid with long edges at right angles to joists
  • short edges should be supported on joists or noggings or cut back to form a butt joint over a joist
  • boards should be glued to the joists and the sheets glued to each other with polyvinyl acetate (PVAc) adhesive (not softwood boarding)
  • long edges at room perimeters should be fully supported on joists or noggings.

Chipboard flooring

Chipboard flooring should be supported and fixed in accordance with manufacturers’ recommendations using either:

  • flat-headed ring shank nails, 2.5 x the thickness of the board and minimum 3mm diameter, or
  • screws to BS 1210, minimum 2 x the thickness of the board and no less than size No. 8.

When fixing:

  • fixings should have a maximum spacing of 300mm along continuously supported edges and intermediate supports
  • where boards abut a rigid upstand, a minimum 10mm expansion gap should be provided; for large areas of boarded floor, a wider expansion gap may be required at upstands and intermediate expansion gaps of 2mm per linear metre of floor should be provided.

Oriented strand board flooring

When fixing oriented strand board flooring:

  • boards should be laid over supports in the direction indicated on the board, with the stronger axis at right angles to the supporting joists
  • boards should be long enough to span two joists
  • nails should be flat headed, annular grooved nails, 3mm in diameter
  • where boards abut a rigid upstand, a minimum 10mm expansion gap should be provided; for large areas of boarded floor, a wider expansion gap may be required at upstands and intermediate expansion gaps of 2mm per linear metre of floor should be provided.

Plywood flooring

When fixing plywood flooring:

  • boards should be laid with the face grain at right angles to the supports
  • end joints should occur over joists or noggings
  • fixings should have a maximum spacing of 150mm around the perimeter and a maximum spacing of 300mm on intermediate supports
  • an expansion gap of at least 1.5mm-2mm should be allowed between each panel.

Nails for fixing plywood should be in accordance with Table 8.

Table 8: Fixings for plywood floors

Plain wire nails (mm)Annular ring shank nails (mm)
Minimum diameter3.353
Minimum length6550
Minimum penetration4032

Proprietary flooring

Proprietary flooring should be:

  • certified in accordance with Technical Requirement R3
  • installed in accordance with certification requirements.

Protection against damage

Floor decking should be stored:

  • on a hard base
  • under cover
  • indoors where possible.

Where timber decking is to be installed before the home is watertight, the manufacturer should confirm suitability.

Floors should not be overloaded, especially with materials during construction, and be protected against damp, plaster splashes and other damage.