Internal walls

6.3

Also See:

6.1

6.4

9.2

6.3.4Masonry walls

Internal masonry walls shall be designed to support and transfer loads to foundations safely and without undue movement. Issues to be taken into account include:

structural elements
mortar mix and jointing
workmanship
bonding and tying
lateral restraint
masonry separating walls
lintels and beams.

Structural elements

Structural design of masonry walls should be in accordance with BS EN 1996-1-1.

Bricks and blocks should be selected in accordance with their intended use and as recommended in Table 1.

Table 1: Bricks and blocks in buildings up to three storeys high

Height of wall	Unit	Minimum compressive strength
One or two storey	Blocks Bricks	2.9 N/mm2 9.0 N/mm2
Lowest storey of a three storey wall, or where individual storeys exceed 2.7m	Blocks Bricks	7.3 N/mm2 13.0 N/mm2
Upper storeys of a three storey wall	Blocks Bricks	2.9 N/mm2 9.0 N/mm2

Where buildings are more than three storeys high, masonry should be designed in accordance with Technical Requirement R5 and the block strength specified in the design.

Precast concrete blocks

Concrete blocks should comply with BS EN 771. The maximum load-bearing capacity of the wall should not exceed the recommendations of the manufacturer.

Flue blocks should be in accordance with the manufacturer’s recommendations.

Bricks

Bricks should comply with the relevant British Standards:

Clay bricks	BS EN 771-1
Calcium silicate bricks	BS EN 771-2
Concrete bricks	BS EN 771-3

When used in a separating wall, masonry should:

be in accordance with the design information

provide a suitable level of sound resistance.

Mortar mix and jointing

Mortar should:

be the correct mix and used within two hours, unless it is retarded mortar

not be re-tempered if it has started to set

include sulfate-resisting cement where required.

Admixtures, retarded mortars and premixed mortars should be:

compatible with masonry and other components

used in accordance with the manufacturer’s recommendations.

Air-entraining agents:

can help reduce frost damage but cannot be used as anti-freeze

should be carefully measured for each batch and be in accordance with the manufacturer’s instructions.

Bricks and blocks should be laid on a full bed of mortar, with perpends solidly filled.

Where walls are to be finished with wet plaster, joints should be raked out to a shallow depth to provide a key. For dry lining, mortar joints should be struck off flush.

Workmanship

Internal masonry walls and associated works should be:

constructed in lifts/stages to prevent the distortion of wall panels during construction

accurately set out

reasonably plane and true

plumb, with courses level.

Bonding and tying

Internal masonry walls should:

maintain a regular bonding pattern

not include bricks or blocks of different types in the same wall, to avoid cracking

be fully bonded or tied, either with a tooth at alternate courses, or an expanded metal tie (or equivalent) at a maximum vertical spacing of 300mm.

Lateral restraint

Load-bearing masonry walls, including separating walls, should be provided with lateral restraint at:

each floor level

ceiling level below a roof.

Restraint straps should be provided to separating walls on each level, at a maximum of 2m centres, when the floor:

is not on, or near, the same level

does not provide adequate restraint.

Lateral restraint should be provided in accordance with Chapter 6.4 ‘Timber and concrete upper floors’.

Timber floors

Adequate restraint can be provided by timber floors where joists have a minimum 90mm bearing. Alternatively, restraint should be provided by:

restraint straps with a minimum 30mm x 5mm cross-section, or

restraint type joist hangers to BS EN 845-1 with a performance equivalent to restraint straps.

Concrete floors

Adequate restraint can be provided by concrete floors that have a minimum 90mm bearing on to the wall. Alternatively, restraint should be provided by:

restraint straps that are a minimum of 450mm long with the end turned down between a joint in the concrete floor or suitably fixed with screws.

Masonry separating walls

Both leaves of a masonry cavity separating wall should be tied together to provide structural stability. The type of tie and spacing should limit the sound transmission across the cavity in accordance with building regulations.

Lintels and beams

Lintels should be specified according to loads and spans:

in accordance with manufacturer’s recommendations, or

For masonry:

concrete and steel lintels are suitable

timber lintels should not be used

lintels should extend beyond the end of each opening in accordance with Table 2.

Table 2: Lintel bearings

Span (m)	Minimum length of bearing (mm)
Up to 1.2	100
Over 1.2	150

Lintels and beams should:

have padstones where required

be the correct way up

bear on a full block, and be level and bedded on a solid bed of suitable mortar

not have soft or non-durable packing.